This is a generally normal inquiry in hearth item looks around the country. There are numerous items intended for this particular application. In any case, assuming this is a wood-consuming oven, the response is most certainly “no”! Peruse on to improve comprehension of certain subtleties with regards to changing over a wood-consuming fireplace with a characteristic or LP gas embed.


An advantageous and simple-to-work gas addition can be introduced in open-consuming workmanship or a zero leeway (ZC), industrial facility assembled metal wood-consuming fireplace. A gas embed is a natural gas fireplace (either normal or LPG) that has been intended to slide into a current wood-consuming fireplace. Embeds are brilliant warmers, utilizing the gas that is scorched. Many discretionary fronts and media decisions can make a gas fireplace embed mirror your tastes and way of life.

Manufacturer of fireplaces:

So that nothing is visible before the fireplace or on the hearth, an electric and gas supply line should be installed inside the handmade firebox.  Both the gas and electric lines can be introduced from the cellar on a regular basis, through the clear-out hole, and by removing the little rubbish dump entryway at the bottom of the old fireplace.

Access openings to the electrical association and the gas supply line are provided by gas embeds. Thus, once introduced into the firebox, these associations with the gas fireplace embed are generally clear. Two adaptable aluminum liners are connected to the highest point of the supplement and introduced up the current smokestack to appropriately vent the gas embed.

The damper on the stonework fireplace ought to be either taken out or forever crippled to forestall any harm to the venting framework. The old, existing smokestack cap should be eliminated and another end cap for the aluminum liners will be introduced.

Every so often, an old, crumbled smokestack is taken out underneath the roofline and concealed in the storage room region. This ought not to forestall a gas fireplace embed from being introduced. The two adaptable, aluminum liners can be introduced to the surprise of no one. The highest point of the old fireplace will be revealed to oblige exceptional retro connectors. These connectors will permit a co-direct (two-line) framework to be changed over to a co-pivotal vent framework.

After the supplement is introduced, an embellishing board is utilized to wrap up the venture. This board is planned to close the remainder of the old fireplace opening. Normally, made of steel, these boards come in standard sizes or can be uniquely requested for bigger fireplaces or surprising conditions.


Chances are high that a supplement can be introduced assuming yours is a ZC, manufacturing plant fabricated, metal wood-consuming fireplace from the 70s, 80s, or 90s. Getting the electric and gas lines into the firebox can in some cases make this period of the undertaking somewhat really testing.

An opening for the gas and electric lines might be penetrated through the side or lower part of the current ZC fireplace, contingent upon where the entrance openings are situated on the gas embed. Once more, the damper ought to be taken out or for all time hindered open.

A two-liner framework is utilized to accurately vent the gas embed and to give burning air. On the off chance that the two-walled tempered steel chimney stack for the old wood fireplace is looking great, the two liners would end at the extremely top.

Once more, the old smokestack cap is history, and another upward end pack is utilized to supplant it. If a section or two of the previous 8″ or 10″ smokestack has been removed or is in danger of being removed, replace connectors, as shown above, from a co-straight to a co-pivotal venting framework.

Despite the fact that there are standard sizes of encompassing boards for ZC fireplaces, many are specially crafted. This gives the old fireplace a make-over and will conceal old, stained metal accents or a stained and filthy fireplace face.


Unsupported wood-consuming ovens are not possible to be changed over to gas. They can be supplanted with gas, yet not changed over to gas. There are no gas embeds or gas logs that have been planned, tried, and supported to be introduced into a current wood-consuming oven. This question comes up intermittently. Try not to endeavor this. It tends to be amazingly risky.

Gas ovens are regularly used to supplant a wood-consuming oven. The wood oven and dark connector dark should be taken out. When a gas supply line is introduced to the hearth, the new gas oven is put in a similar spot, and a co-hub pipe is introduced to the stack opening.

Once in the stack, the persuade pipe is retrofitted with connectors that convert it to a co-direct framework. From here, similar to the next venting situations clarified over, the adaptable aluminum liners are introduced up the current stack and ended on top with another cap.

Related Articles

Leave a Reply

Back to top button